- Bear crossbow recommended bolts how to#
- Bear crossbow recommended bolts full#
- Bear crossbow recommended bolts pro#
Their purpose was to deliver a wide cutting edge so as to kill as quickly as possible by cleanly cutting major blood vessels in the enemies they struck. & 325-375 FPS.Īrrows & Bolts: Drop, Energy, Trajectories, Broadheads & Broadhead Tuning.īroadheads were originally designed for war usage.
Bear crossbow recommended bolts how to#
Chances are they've encountered your issue before and have several options on how to fix it, the right way.Crossbows: Compound, Designs, Directory, Draw Weight, History, Hunting, Modern, Recurve, Reviews & Terminology.Ĭrossbow Manufacturers: Barnett, Excalibur, Horton, Parker & Tenpoint.
Bear crossbow recommended bolts pro#
Take your crossbow to the local pro shop and have someone look at it. If the solutions prescribed don't work, don't panic. When in DoubtĪs noted, these are some of the more common issues and answers there may be others. Using the wrong nocks could also result in more serious issues than poor accuracy.
Bear crossbow recommended bolts full#
Crossbow makers may recommend a specific nock type (flat, half-moon, etc.) for a variety of reasons, such as a long power stroke resulting in a steep string angle at full draw or the claw pivot being above or below the rail. When in doubt, check the manufacturer's recommendations.įourth, check to see if you are using the proper nocks. Going the other way – using a lighter, less stiff bolt than recommended – can be more problematic, particularly with faster crossbows that transfer more energy to the shaft. You can overcompensate – use a heavier bolt with a stiffer spine – without too much of a problem. Third, make sure you are using a bolt with the proper spine for your bow. If anything is loose, tighten it up and your problem is probably solved. First, check all the screws, nuts and bolts holding your optic in place. So, let's go through a few of the most likely. You should also check that the arrow-retention spring is in good working order, as this piece is often connected to the ADF.Ĭrossbow fails to group well: There are several possibilities here. I've seen it happen on a crossbow where the ADF malfunctioned.
The results can be as bad or worse than a dry fire. It's a good thing, because were that not the case, the bow could fire with a bolt in place but not in contact with the string. What's happening is that the bolt is not seated far enough back to make contact with the string and, more importantly, disengage the anti-dry-fire mechanism (ADF). I've encountered this issue several times with my fishing crossbow, probably because it spends so much time pointed downward.Īll things considered, this is a good problem. However, a far more likely cause is that the bolt is not pushed all the way back, or has slid forward. When cocked and loaded, crossbow fails to fire: It's possible that as in the previous example, the bow was not fully cocked. However, something is not working properly, and I would advise taking the bow to your local pro shop or contacting the manufacturer or place of purchase about possible repair or replacement. One solution is to simply click the safety on after cocking and continue as usual. Safety did not engage while cocking, but crossbow will fire: It shouldn't happen, but I've encountered this on bows from several different manufacturers. You should be able to simply re-attach your cocking mechanism and pull back farther, until you hear a distinct "click" and see that the safety has engaged. In other words, the string wasn't pulled all the way back, far enough to cock the bow and engage the safety mechanism. Safety did not engage while cocking, and crossbow will not fire: In all likelihood, the bow was short-cocked. In that case, make sure you are pulling the string all the way back. That used to be necessary on some crossbows, but for the most part, it no longer matters whether the safety is on safe or fire when cocking. Common ProblemsĬrossbow will not cock: This is less common than it used to be but could well be the result of not having the safety mechanism in the "fire" position while cocking. Below, I've listed five of the more common issues crossbow shooters might encounter, along with their causes and solutions. Regardless, sometimes our crossbows don't perform as well as we'd like.
Sometimes, it's a matter of materials or manufacturing.
0 kommentar(er)
